Programmable 408L ESS Chambers Thermal Shock Chamber With Water Cooled ESS-408LL10 manufacturer from China KOMEG Technology Ind Co., Limited

Programmable 408L ESS Chambers Thermal Shock Chamber With Water Cooled

Place of Origin:

Zhejiang, China (Mainland)


	Add to My Favorites
HiSupplier Escrow	Share \|

Product Detail

Model No.: ESS-408LL10

ESS Testing 408L Volume 15 ºC /MinRapid-Rate Thermal Cycling Chamber

<

ESS Testing 408L Volume 15 ºC /MinRapid-Rate Thermal Cycling Chamber

1. What is ESS?

1.1 Environmental Stress Screening (ESS) is a means of screening electronic assemblies at the most cost-effective point of manufacture to expose defects that can't be detected by visual inspection or electrical testing. These defects are typically related to defective parts or workmanship and are normally found as early field failures.

ESS works by subjecting 100% of a group of products to an environmental stimulus or a set of stimuli for a predetermined time for the purpose of forcing failures to occur before shipment, in fact, at the board level.

Failures are normal and expected when ESS is applied. This makes ESS radically different than more conventional certification testing which requires failurefree operation as proof of reliability.

1.2 ESS is not a test, it is a process.

Key factors for proper ESS implementation are:

1) The stress environment must not exceed the electrical or mechanical limits of the product.

2) An optimum level of stress must be applied to the product.

1.3 Expected benefits of a properly applied ESS program are:

1) Reduced field repair expense

2) Fewer defects and waste

3) Elimination of less effective screening procedures

4) Lower unit cost

5) Increased product value

6) Improved customer satisfaction

7) Better return on investment (ROI)

2. Specifications

Model	ESS-LL
Model	408LL10
Working Chamber Volume(L)	408L
Temp Rate of Change( ºC /Min)	10 ºC /Min
Temperature Range	-70 ºC+100 ºC( Rapid Temp Change -40 ºC+85 ºC Full Linear Control)
Humidity Constancy	±0.5 ºC
Temp Constancy	±3.0 ºC
Exterior Material	Cold-rolled steel sheet (Rust proof & Plastic Spray treated )/ Stainless Steel
Interior Material	Stainless Steel Plate(SUS 304)
Insulation Material	Rigid Polyurethane Foam
Safety Devices	over pressure,over heat and over current protection for compressor, over temp. protection,
Compressor	Semi-Hermetic Compressor
Cooling Mode	Water Cooled
Control system	Balanced Temperature & Humidity Control System(BTC type)
Heater	Iron-chrome wire heater
Blower	Centrifugal Blower
Observation Window	Glass incorporating heat generator
Temp Sensor	Pt-100
Controller	Touch screen programmable controller
Ambient Temp.	+5ºC~+35ºC
Power	AC 380V/50Hz 3phase 5 wires+ Ground wire
Note: 1. We reserve the right to change specifications without prior notice 2. Customized sizes and configurations available

3. Function and Features

a. The ESS Test Chamber is mainly used in testing the adaptability of electronics, electrical appliances, food, automobile, rubber and plastic, metal and other products, parts and materials in the high and low temperature alternating hot and humid environment when storage, transport and using

b. It is an reliable test equipment for all kinds of electronic, electrical, electronics, plastics raw materials and devices to do testing such as cold, heat, moisture, resistance to dry and the quality control

c. The new perfect design, the appearance of high texture level, the system extracts Japan, West Germany, the essence of design and manufacture of advanced technology.

d. Balanced temperature humidity control system (BTHC), to PID mode control SSR, so that heated humidification system was equal to heat loss capacity, it could be used long-term stability;

e. All-capillary, automatic load capacity adjustment system technology, more expansion valve system more stable and reliable, precise temperature and humidity control, heating and cooling rate of rapid, steady, uniform, saving valuable time for users.

4. Besides this, we also provide other climatic chambers: